Description

Feature Products 15KV High Voltage Generator step-up Electric Ignitor arc Lighter Coil DIY Suit Booster Coil Inverter Heat sink Note: This item is DIY Kit, not assembled. Description: 100% brand new and high quality Color: White Features: This product is a booster coil production suite, the circuit is simple and reliable, with a professional line drawings, electronic research convenience enthusiasts Uses: high school science experiment, electronic equipment, negative ion generator, scientific small production. This circuit is generated when the stable high frequency arc, high temperature, can easily ignite combustible materials, so it was called the plasma lighters Parameter 15KV transformer outside dimensions of approximately: 27×16×21mm Input voltage: DC 3.7V-4.2V (limit 12v, easy to damage not recommended, this transformer is equally applicable to 12V input voltage, but requires a corresponding increase in the base of the feedback resistor to about 150Ω ~ 1.5KΩ, its resistance should be large to replace a small adjustment, or burned transistor or transformer) Input Current: <1.5A Output voltage: approximately 15KV (please pay attention to safety when used) Output Current: ≤0.4A High voltage bipolar ignition distance: ≤0.5 cm When the product input termination 3.7V-4.2V power supply, the secondary high voltage output is not connected to high-voltage rectifier diodes and capacitors, output terminals levels ≤1.5 cm long can produce purple high temperature arc, no crackling, but the temperature is very high , you can easily and instantly point cigarette paper, or even very thin wire burned Sparks (such as junior high school chemistry experiment thin wire in oxygen combustion scene, but not as good as oxygen so intense.) Transformer structure There are two primary windings, a primary winding, a feedback winding, the secondary output of high pressure. Other: 15KV transformer designed for maximum output, limit output can not exceed 15KV, is one centimeter arc, a higher output voltage is likely to damage the transformer. Quantity: 1 set Note: Please allow 1-2mm errors due to manual measurement Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! Package includes: 1 x 15VKE = 1 type step-up transformer one 1 x 120 ohms resistance 1 x UF4007 ultra-fast recovery diode 1 x D880 transistor 1 x heat sink 1 x M3 * 6 screws 1 x Boat switch 1 x 3 pin Generator Arc Ignition Coil Note: This item is DIY Kit, not assembled. default with one PCB board. Features: This product is a booster coil production suite, the circuit is simple and reliable, with a professional line drawings, electronic research convenience enthusiasts Uses: high school science experiment, electronic equipment, negative ion generator, scientific small production. This circuit is generated when the stable high frequency arc, high temperature, can easily ignite combustible materials, so it was called the plasma lighters Parameter: 15KV transformer outside dimensions of approximately: 27×16×21mm Input voltage: DC 3.7V-4.2V (limit 12v, easy to damage not recommended, this transformer is equally applicable to 12V input voltage, but requires a corresponding increase in the base of the feedback resistor to about 150Ω ~ 1.5KΩ, its resistance should be large to replace a small adjustment, or burned transistor or transformer) Input Current: <2A Output voltage: approximately 15KV (please pay attention to safety when used) Output Current: ≤0.4A High voltage bipolar ignition distance: ≤0.5 cm When the product input termination 3.7V-4.2V power supply, the secondary high voltage output is not connected to high-voltage rectifier diodes and capacitors, output terminals levels ≤1.5cm long can produce purple high temperature arc, no crackling, but the temperature is very high , you can easily and instantly point cigarette paper, or even very thin wire burned Sparks (such as junior high school chemistry experiment thin wire in oxygen combustion scene, but not as good as oxygen so intense.) Transformer structure: There are two primary windings, a primary winding, a feedback winding, the secondary output of high pressure. Other: 15KV transformer designed for maximum output, limit output can not exceed 15KV, is one centimeter arc, a higher output voltage is likely to damage the transformer. PCB board size: 4.2CM * 3.2CM * 0.16CM; Installation Notes: 1). With the PCB board parts better production, in which the transformer line of thick line and thin line, this should pay attention to the other components by the board of silk symbols and parameters of welding on the line. Transformer board has done three pads, in which the middle of the pad hole is relatively large, the hole at the same time welding a thick enameled wire and a thin enameled wire, thick enameled wire and fine enameled wire do not use the same side, such as with the left Thick lines and the right side of the thin wire into or with the left side of the thin line and the right side of the thick line welding into, in short, do not use the same side of the thick lines and thin lines can be. 2). In order to prevent the output 2-wire distance too far, resulting in no-load, you can weld a 3P pin at the output. 3). After the success of the production, if the output access to a high-voltage capacitor and three high-voltage rectifier composed of voltage doubler circuit, you can produce DC high voltage, you can make anion generator, wiring diagram is as follows: Package Included: 15VKE = 1 type step-up transformer x1 PCB Board X 1 120 ohm resistance X 1 UF4007 ultra-fast recovery diode X 1 N20 transistor X 1 Heat sink X 1 M3 * 6 screws X 1 Boat switch X 1 3-Pin X 1 Shipping Policy Item Location Payment Mathord Returns Policy About Feedback Shipping Policy 1. We Ship to Worldwide 2. We ship your orders within 1-2 business days after the payment cleared. 3. Item shipped from China via china Post Airmail, reach most of the countries within 2 to 4 weeks. 4. Delivery time depends on destination and other factors, it may takes up to 20 days. If you don't receive the item after 30 days,please keep in touch with us, we'll investigate and solve the delivery problem. 5. Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying. Item Location ShenZhen Payment Mathord 1. We accept PAYPAL only. 2. Payment must be made within 7 days of auction closing (Unpaid dispute will automatically open when item is not paid in 7 days). 3. PLEASE NOTE: SHIPPING&HANDING DOES NOT INCLUDE DUTIES, LOCATL TAXES OR ANY OTHER IMPORTATION FEES. 4. Please list your special requests (color, packages, value of declaration, etc.) in the EBAY NOTES SECTION when you make payment Returns Policy 1. Customer satisfaction is our top goal. All products are quality checked. They are new and in good condition when shipped to our customers. If product is defective or damage upon arrival, or wrong product shipped, please keep in touch with us immediately. Returns accepted within 14 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer. 2. Please keep in touch with us first if you have anyproblems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner. 3. We appreciate your Positive Feedback, and will do the same in return. PLEASE DO NOT leave negative feedback without first communication with us. Please allow max 24 HOURS for us to respond About Feedback We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.It is impossible to address issues if we do not know about them!